A Massey Ferguson 35 bonnet kit is the sheet metal front end of the tractor: the bonnet top, the left and right side panels, the front grille and the lower front panel. Most kits are panels only. So the pivot bolts, grille studs, clamping pins, handles and rubber strip are usually bought separately. First, check whether your tractor has the 3-cylinder or the 4-cylinder engine, because the kits differ.
This guide is for dealers, workshops and restorers who order MF35 tinwork. In the USA the same panels are called the hood and sheet metal. Below you will find what each panel does, the fixings to add to your order, a dry-fit routine and a checklist to send with your enquiry.
Last updated: 4 November 2026
What is in a Massey Ferguson 35 bonnet kit
The front of an MF35 is not one pressing. Instead, it is four or five panels bolted together around the radiator and the engine. A kit gives you all of them at once, so the lines match. The table shows each panel, what it does, and the single part we make if you only need one piece.
| Panel | What it does | Our single part | OEM number it replaces |
|---|---|---|---|
| Bonnet top | Covers the top of the engine. On the 3-cylinder it has a hinged lid with handles. | Bonnet top, MF35X 3-cylinder | 1861842M91 |
| Side panels, left and right | Close the sides of the engine bay below the bonnet top. | Side panel, MF35 3-cylinder | Not yet listed |
| Front grille | Lets air reach the radiator and guards it from stones. | Front grille, MF35 3-cylinder | 826812M91 |
| Lower front panel (chin) | Closes the nose below the grille. | Lower front panel, MF35 3-cylinder | 826817M92 |
Our Massey Ferguson 35 bonnet kit (part AME001) is listed for the Pre 100 Series 35 3-cylinder. Its product photo shows the front end assembled: the top with its lid, a side panel, the grille and the lower front panel. However, kit contents vary between suppliers. For that reason, ask for the itemised list of pieces with your quote, and compare it with this table.

3-cylinder or 4-cylinder: check before you order
The MF35 was built with the Standard 4-cylinder engine and, from 1959, the Perkins 3-cylinder diesel. The tinwork changed with the engine. For example, the UK parts list at Agriline for the FE35 4-cylinder offers a separate grille and panel set “for 4 cylinder models” and a bonnet with a chrome push button. By contrast, its MF35 3-cylinder list has a bonnet lid handle kit instead.
So a 3-cylinder MF35 bonnet will not simply drop onto a 4-cylinder tractor. If you are not sure which engine you have, our guide on how to identify a Massey Ferguson 35 explains the plate letter and the exhaust check. Also note that an engine may have been swapped. In that case, order for the engine fitted now.
Fixings to order with a Massey Ferguson 35 bonnet kit
A panel kit arrives without the small parts that hold it together. In fact, the MF35 3-cylinder list at Agriline says its own bonnet kit requires a fixing kit, two bonnet pivot bolts, two grille studs and a bonnet lid handle kit. The same list shows the other fixings for the front end. Here is what to check on your tractor:
- Bonnet pivot bolts, two. The bonnet top pivots on these. Agriline lists them as 7/16 inch UNF thread.
- Grille studs and grille fasteners, two of each. They hold the grille in place.
- Bonnet clamping pins, two per tractor. Check them for wear before you reuse them.
- Bonnet lid handles, a pair. The 3-cylinder handle kit comes with its own fixings.
- Bonnet clips, studs and nuts. These small parts often rust solid and are cheap to replace.
- Dash rubber. It seals the gap between the bonnet and the dash panel.
Alternatively, a general fastener kit covers the nuts, bolts and washers. Sparex, for instance, sells a bonnet fastener kit listed for the 35, 35 Gas, 35 Petrol, 35X and FE35. Reuse the old fixings only if the threads are clean and the pins are not worn.
How an MF35 bonnet fits: dry fit before you paint
Fit problems are the main complaint about aftermarket MF35 tinwork. For example, one owner on TractorByNet bolted new side panels and a new chin panel to the original bonnet top. As a result, the lines were poor, the holes did not match, and the owner worried the lower pivot bolts would not line up. Therefore, test the fit before any paint goes on.
A dry-fit routine
- Photograph the old front end from the front and both sides before you take it off. These photos show where every bolt goes.
- Remove the old panels and check the mounting points on the tractor. Straighten bent brackets first, since a bent bracket moves every panel after it.
- Lay out the new panels and compare each one with the old one. Count the holes and check their position.
- Fit all the panels with the fixings finger tight. Then look at the gaps and the lines from the front and both sides.
- Check that the bonnet top pivots and closes, and that the pivot bolts go in without force.
- Once everything lines up, take the panels off, prepare and paint them, and refit with the new rubber and fixings.
Mixing new panels with an old bonnet top is where most gaps appear. If your old top is dented or rusted through, a full kit is usually the better choice. On the other hand, if the top is sound, buy only the panels you need, and dry fit them against it.
Checklist to send with your enquiry
With these details a supplier can match the panels on the first try. Without them, expect a round of questions before the quote.
- The model badge: 35, 35X or FE35.
- The engine: 3-cylinder or 4-cylinder, and the fuel.
- Full kit, or which single panels you need.
- Any number stamped on the old panels.
- Photos of the old front end, showing the mounting holes.
- The fixings you need, from the list above.
- The quantity of each item.
Massey Ferguson 35 bonnet kit from Ajva Motors
We make aftermarket sheet metal body parts at our factory in Gujarat, India, and have done since 1998. Our Massey Ferguson 35 bonnet kit and its single panels are pressed from steel sheet and painted in red oxide. The minimum order is 5 pieces per product, and we send a sample on request, so you can dry fit one before the full order. We reply to quotes within 24 to 48 hours on business days.
You can see every panel we make for this tractor on the Massey Ferguson 35 3-cylinder parts page. Our tractor bonnets page lists the bonnet tops for other models. For the Ferguson TE20, read our TE20 bonnet kit guide.
Questions about the MF35 bonnet kit
What comes in a Massey Ferguson 35 bonnet kit?
Usually the bonnet top, the left and right side panels, the front grille and the lower front panel. Contents vary by supplier, so ask for the itemised list with your quote.
Does an MF35 bonnet kit include the bolts and fixings?
Usually not. Plan to add the pivot bolts, grille studs, clamping pins, lid handles, clips and dash rubber, or a fastener kit for the 35.
Will a 3-cylinder kit fit an FE35 4-cylinder?
Do not assume it will. UK parts lists give the 4-cylinder its own grille and panel set and a different bonnet catch. Check the engine first, then order for that engine.
Can I fit new side panels to my original bonnet top?
You can, but this is where gaps show most. Dry fit the new panels against your top before painting, and fit a sample first if you are ordering several.
Should I paint the panels before fitting?
No. Dry fit them first, adjust anything that needs it, then paint. Otherwise any drilling or adjustment damages the new finish.
Ready to order a Massey Ferguson 35 bonnet kit? Send the checklist details and photos through our contact page, and we will confirm the parts before you order.
