Here is how to identify Massey Ferguson 35 tractors in four checks. First, read the letters and number on the commission plate on the dashboard. Next, check the paint: grey and gold means an early Ferguson FE35. Then see which side the exhaust is on, which tells you 3 or 4 cylinders. Finally, look for badge holes in the bonnet. Together these tell you whether you have a TO35, FE35, MF35 or MF35X.
This matters before you order tinwork. Parts sellers list the 35 by engine, and a panel listed for the 3-cylinder may not be the one your tractor needs. This guide is for restorers, dealers and parts buyers in the UK, Ireland and the USA. Where the sources disagree on a date or a serial number, we say so.
Last updated: 27 October 2026
How to identify Massey Ferguson 35 models: the four names
The same basic tractor carried four names. The name depends on where it was built and when. According to Wikipedia’s Massey Ferguson 35 article, the American version came first, in January 1955. The British version followed in 1956.
| Name | Built | Years | Original colours | Engines |
|---|---|---|---|---|
| Ferguson TO35 | Detroit, USA | 1955 to 1960 | All grey, then beige and grey from May 1956, then red and grey from December 1957 | Continental Z134 petrol (gas) |
| Ferguson FE35 | Banner Lane, Coventry, UK | 1956 to 1957 | Grey tinwork and wheels, bronze (gold) engine and transmission | Standard 4-cylinder petrol, vaporising oil (TVO) or 23C diesel |
| Massey Ferguson 35 (MF35) | Coventry and Detroit | 1957 to 1964 | Red tinwork, grey engine and transmission | Standard 4-cylinder petrol or TVO; Standard 23C diesel to 1959; Perkins 3-cylinder diesel from 1959 |
| Massey Ferguson 35X | Coventry | 1962 to 1964 | Red and grey | Perkins A3.152 3-cylinder diesel |
The MF35 name came in after Ferguson and Massey Harris became Massey Ferguson. However, when you work out how to identify Massey Ferguson 35 tractors, the badge is the weakest clue of all. Old tractors are often repainted and rebadged.
Step 1: read the Massey Ferguson 35 serial number plate
The Massey Ferguson 35 serial number is the best place to start. On British tractors, it is on a small plate on the lower right of the dashboard, next to the ignition key. The plate shows a group of letters and then a number, for example SDM 45120.
The letters describe how the tractor left the factory. The Ferguson Club’s guide to the FE35 letter code decodes them as follows.
| Position | Letter | Meaning |
|---|---|---|
| 1st: tractor type | S, V, J, C | Standard agricultural, vineyard, industrial, high clearance |
| 2nd: engine | G, H, K, L | Petrol, high altitude petrol, vaporising oil (TVO), lamp oil |
| 2nd: engine | D | Standard 23C diesel, 4 cylinders |
| 2nd: engine | N | Perkins A3.152 diesel, 3 cylinders |
| 3rd: clutch | F, M | Single clutch, dual clutch (live PTO) |
| 4th: extras | Y | Differential lock |
So the second letter answers the cylinder question straight away. N means a Perkins 3-cylinder. D, G, K, L or H means a 4-cylinder engine. As a result, SNM is a standard tractor with a Perkins diesel and a dual clutch.
Date the tractor from the Massey Ferguson 35 serial number
Next, the number gives the year, which is the second half of how to identify Massey Ferguson 35 tractors from the plate. The Anglo-Agriparts serial number list gives the first number built each year at Coventry.
| Year | First serial number | What changed |
|---|---|---|
| 1956 | 1001 | First Ferguson FE35, grey and gold |
| 1957 | 9226 | Grey and gold tinwork up to serial 74655, then red and grey |
| 1958 | 79553 | |
| 1959 | 125068 | Perkins 3-cylinder diesel from serial 165596 |
| 1960 | 171471 | |
| 1961 | 220614 | |
| 1962 | 267528 | MF35X from serial 302413 |
| 1963 | 307231 | |
| 1964 | 352255 | Last tractor 388382 |
For example, a plate reading SNM 180000 is a 1960 tractor with the Perkins engine. In contrast, SDM 50000 is a 1957 Ferguson FE35 diesel that left the factory in grey and gold. If the plate is missing, the engine number will not date the tractor accurately. The Ferguson Club notes that engine and tractor numbers rise together but do not match.
Serial numbers on American tractors
American tractors have their own list. For instance, the Ferguson Enthusiasts of North America date SGM 210485 to late 1960, which makes it an MF35. In their reading, S is a standard chassis, G a gas engine and M a dual clutch.
Step 2: how to identify Massey Ferguson 35 colours, with care
The Ferguson FE35 is known as the “Gold Belly”. It had grey tinwork and wheels, with a bronze or gold engine and transmission. Then in 1957 the British tractor changed to red tinwork with a grey engine and transmission.
The American TO35 went through three schemes. It was all grey at launch, beige and grey from May 1956, and red and grey from December 1957. Because the same red and grey covers seven years of tractors, colour on its own says little after 1957.
Also, many of these tractors have been repainted at least once. To check, scrape a little paint from a hidden spot on the transmission housing. Gold under grey points to an FE35. If the paint disagrees with the serial number, trust the serial number.
Step 3: how to identify Massey Ferguson 35 engines by the exhaust
For anyone learning how to identify Massey Ferguson 35 tinwork, this check matters most. From 1959, the Perkins 3-cylinder diesel replaced the Standard 4-cylinder diesel. However, the 4-cylinder petrol and TVO engines stayed on sale until 1964. So a 4-cylinder MF35 is not always an early tractor.
Fortunately, the exhaust tells them apart from a few feet away. According to the Tractor and Construction Plant Wiki, sitting in the seat and looking forward:
- 4-cylinder: the exhaust is on the right, the same side as the brake pedals.
- 3-cylinder: the exhaust is on the left, the same side as the clutch pedal. The same goes for the MF135 3-cylinder.
Then confirm with the plate. N in the second position means the Perkins 3-cylinder. Finally, if an engine has been swapped, the exhaust shows the engine fitted now. That is the engine your bonnet and side panels must suit.
Step 4: how to identify Massey Ferguson 35 bonnets by badge holes
Owners on the Historic Commercial Vehicle Club forum in Australia describe how the FE35 badges were fixed. Each side badge sat on the bonnet near the battery and used three holes. The front badge used two. A bonnet with no badge holes may be a later red and grey one badged MF35.
Treat this as a supporting clue only. It comes from owners, not from factory records. The same thread mentions that some dealers repainted the last FE35s and sold them as MF35s. Also, a bonnet may have been replaced at some point in the last sixty years.
Where the sources disagree
Dates for these tractors differ from one reference to the next. Anyone who has looked up how to identify Massey Ferguson 35 models will have seen this. Here are the differences we found, so you can judge for yourself.
| Point | One source says | Another says |
|---|---|---|
| When the TO35 name started | 1954 (Ferguson Enthusiasts of North America) | Launched 5 January 1955 (Wikipedia) |
| When the FE35 became the MF35 in the UK | 1957, after 73,655 tractors (Wikipedia) | Ferguson badges until 1958 (Anglo-Agriparts) |
| When the MF35X came in | Launched 8 November 1962 (Wikipedia) | Introduced in 1963 (Tractor and Construction Plant Wiki) |
| First American serial number of 1961 | 211071 (Anglo-Agriparts) | 211072 (Ferguson Enthusiasts of North America) |
In practice, these differences rarely change which panel you need. The serial number and the engine decide that. Some differences come from launch dates versus build dates, and others from tractors that sat in stock and were sold later.
Why this matters when you order tinwork
Parts sellers list many MF35 body panels by engine type. For example, one parts seller lists the bonnet top as an MF35 3-cylinder part, and our own MF35 panels are listed the same way. Ordering the wrong panel is an expensive mistake when it travels by sea. So, as the last step in how to identify Massey Ferguson 35 tinwork, gather these details before you ask for a price:
- The full commission plate: the letters and the number.
- The engine: 3-cylinder or 4-cylinder, and the fuel.
- The model badge on the tractor now: 35, 35X, FE35 or TO35.
- Photos of the old panel from the front and both sides, showing the mounting holes.
- Any number stamped or cast on the old panel.
- How many pieces of each part you need.
With these details, a supplier can match the panel on the first try. Without them, expect a round of questions before the quote.
Which Ajva Motors parts fit the Massey Ferguson 35

Ajva Motors makes aftermarket sheet metal body parts in Gujarat, India, and has done since 1998. Our Massey Ferguson 35 panels are listed for the 3-cylinder tractor. They are the MF35 3-cylinder bonnet kit, the 35 and 35X bonnet top, the front grille, side panel, lower front panel, extension mudguard (fender), footplate kit and tool box. You can see all of them on the Massey Ferguson 35 3-cylinder parts page.
For older tractors, the FE35 and TE20 footplate is listed for the Ferguson FE35, TE20, TEA, TED and 35. If you have a 4-cylinder tractor, send us the plate and photos first. We will tell you whether a panel suits it before you order. For other Massey Ferguson models, see our guide to Massey Ferguson body parts for UK buyers.
Questions about how to identify Massey Ferguson 35 tractors
Where is the serial number on a Massey Ferguson 35?
It is on the commission plate on the dashboard. On British tractors the plate sits on the lower right, next to the ignition key. It shows letters for the tractor type, engine and clutch, then the serial number.
How can I tell a 3-cylinder MF35 from a 4-cylinder?
Sit in the seat and look forward. If the exhaust is on the left, by the clutch pedal, it is a 3-cylinder. If it is on the right, by the brakes, it is a 4-cylinder. N as the second letter on the plate also means the Perkins 3-cylinder.
Is a grey and gold tractor always a Ferguson FE35?
Not always. Grey and gold was the original FE35 scheme up to serial 74655, but tractors are often repainted. Check the serial number. Gold paint under grey on the transmission is a good sign of an original FE35.
What is the difference between the MF35 and the MF35X?
The MF35X came at the end of production, from serial 302413. It has the Perkins A3.152 3-cylinder diesel, which runs at a higher engine speed than the 35’s 3.152. Wikipedia also lists Multi-Power, a system for changing gear without the clutch.
Do 3-cylinder bonnet panels fit a 4-cylinder MF35?
Do not assume they do. Parts sellers often list MF35 panels by engine. Send the serial plate and photos of your old panel to the supplier, and ask them to confirm the fit before you order.
Ask about Massey Ferguson 35 panels
Now you know how to identify Massey Ferguson 35 tractors, send us the plate, the engine type, photos and quantities through the contact page. The minimum order is 5 pieces per part, with a sample on request. We reply within 24 to 48 hours on business days.
