Blog / Buying Guides / Massey Ferguson 135 Restoration: Which Body Panels to Check First
Buying Guides

Massey Ferguson 135 Restoration: Which Body Panels to Check First

November 6, 2026 · AJVA Motors
Tractor Body Parts Exporter in India Ajva Motors makes aftermarket tractor body parts in Gujarat and exports them. MOQ 5 pieces, sample on request.
View Catalog →

On a Massey Ferguson 135 restoration, check the MF 135 body panels in this order: the bonnet top and nose, the footplates, the rear mudguards, the battery cover, then the dash panel and tool box. Of all the MF135 tinwork, the bonnet and footplates hold water and take the most wear. So they decide your budget. Then check whether the tractor has the 13 inch or the 14 inch grille, because the front panels differ.

This Massey Ferguson 135 restoration guide is for restorers, workshops and dealers who buy MF135 tinwork. In the USA the same parts are the hood, fenders and sheet metal. Below you will find a panel by panel checklist, a simple repair or replace rule, and the details to send with an enquiry.

Last updated: 6 November 2026

Before a Massey Ferguson 135 restoration: know your tractor

The MF 135 was the first tractor of the 100 Series and the successor to the MF35. According to its Wikipedia entry, it was launched at the 1964 Smithfield Show and built in Coventry until 1979. Most were fitted with the Perkins AD3.152 3-cylinder diesel. There were also petrol versions.

The bodywork changed during that run. For example, the same source says the design was made more angular in 1965, and updated again in 1971 with a larger fuel tank. As a result, two 135s on the same farm may not share every panel. Before you order anything for a Massey Ferguson 135 restoration, note three things:

  • The serial number and the year, if you have it.
  • The grille height: 13 inch or 14 inch. UK parts lists sell the grille and side panels separately for each.
  • Whether the tractor has Multi-Power, because this changes the switch holes in the dash panel.

Massey Ferguson 135 restoration checklist: panel by panel

Take this table to the tractor. Work from the front to the back, and photograph each panel before you remove it. The last column links to the single part we make, in case one panel is beyond repair.

PanelWhere to lookReplace it whenOur part
Bonnet topThe lid edges, the rear lip at the dash, and the underside along the seamsThe steel is holed or the lip has gone, not just dentedMF 135 bonnet top
Front grilleThe bars, the frame and the fixing pointsBars are broken or the frame is bent out of lineMF 135 front grille
Grille side panelsThe lower edges and the bolt holesBolt holes are torn or rusted out13 inch grille side panel
Grille bracketsCracks around the holesThe grille moves or sits crookedGrille mounting bracket
Dash panelAround the gauge and switch holes, and the joint with the bonnetHoles are split or extra holes have been cutMF 135 dash panel
Battery coverThe underside, where it sits over the batteryIt is thin or holed from belowMF 135 battery cover
FootplatesThe edges, the mounting points and under the matsThe plate flexes when you stand on itMF 135 footplate kit
Rear mudguardsThe mounting holes, the inner edge and the top faceThe mounting area is cracked or patchedMudguard, MF 135 and 148
Extension mudguardsThe bolted joint with the main wingBent, missing or holedMF 135 extension mudguard
Tool boxThe base and the lid hingeThe base has rusted through or the box is missingMF 135 tool box

Massey Ferguson 135 restoration: start with the bonnet top and nose

Start with the bonnet, because it is the largest and most visible panel on a Massey Ferguson 135 restoration. Lift the lids and look at the underside of each seam with a torch. Dents can be dressed out. However, holed steel along the rear lip usually means a new top. Also count the rubber buffers. The Agriline MF 135 body parts list says a tractor needs 24: 10 between the bonnet and the dash panel, and 14 between the bonnet and the nose cone. Missing buffers let the panels rub, so check for wear marks.

If the top, grille and side panels are all poor, a full Massey Ferguson 135 bonnet kit is often simpler than buying each panel. The panels then come as one set, so the lines are easier to match.

Massey Ferguson 135 restoration: MF 135 bonnet kit in red oxide with bonnet top, grille and side panels
Our MF 135 bonnet kit, painted in red oxide.

Grille, side panels and brackets

Next, measure the grille. UK parts lists offer separate 13 inch and 14 inch grille and panel kits, so the measurement decides which side panels you need. Then check the two grille mounting brackets. A cracked bracket lets the grille move, and a new grille will still sit crooked on it.

Dash panel

Then look at the dash panel around the gauges and switches. Owners often cut extra holes for lights or switches over the years. Note that some replacement dash panels are cut for Multi-Power switches. For instance, Agriline says its 135/148 dash panel has these holes, which need blanking plates on a tractor without Multi-Power.

MF135 tinwork: Massey Ferguson 135 dash panel in grey oxide with gauge and switch holes
Our MF 135 dash panel. Compare the holes with your old panel before you order.

Battery cover

Lift the battery cover and turn it over. The top may look sound while the underside is thin, because acid fumes and trapped water attack it from below. Also check the lid handles and catches. They are sold as separate handle kits, in early and later types.

Footplates

After that, stand on each footplate. Mud and water sit under the rubber mats for years. So lift the mats, then check the edges and the mounting points. If the plate flexes under your weight, replace it rather than patch it. Footplates also carry the extension mudguards on some tractors, so check both together.

MF 135 body panels: footplate kit in red oxide for the driver platform
Our MF 135 footplate kit, ready to bolt in place of worn plates.

Rear mudguards, extensions and tool box

Finally, check the rear mudguards (fenders). Look at the mounting holes and the inner edge, where the tyre throws up stones. Extension mudguards bolt to the main wing and come in different drops, so measure the height of the side face. For example, the Agriline MF 148 body list shows a 12 inch drop pair and a mudguard set measured 27 inches from the axle to the top.

Mudguards are often the panels a restorer cannot save. In one Irish restoration covered by the Farmers Journal, every panel on a 1966 MF 135 was original except the mudguards. The owner replaced those, because genuine originals were hard to find. Last, check the tool box base, which collects water and rusts through.

Repair or replace: a simple rule for MF135 tinwork

Most MF135 tinwork can be repaired if the steel is still whole. On any Massey Ferguson 135 restoration, use this rule on each panel:

  • Repair dents, surface rust and small cracks away from the edges.
  • Replace when the rust has gone through, when bolt holes are torn, or when earlier repairs have left heavy filler or patches.
  • Replace in sets when the bonnet top, grille and side panels are all poor, so the front end lines up.

Then dry fit every new panel before painting. A new panel next to an old one can show small gaps, so it is better to find them in bare metal. In the Farmers Journal restoration, the owner sandblasted the body and built up primer and filler before three coats of paint. That level of work is wasted if a panel has to be drilled afterwards.

What to send with your MF 135 body panels enquiry

A clear enquiry saves a round of emails. Send these details with your list of MF 135 body panels:

  1. The model, serial number and year, if known.
  2. The grille height, 13 inch or 14 inch.
  3. Whether it has Multi-Power.
  4. Photos of each old panel, including the mounting holes.
  5. The mudguard drop and, for extensions, the side you need.
  6. The quantity of each panel.

MF 135 body panels from Ajva Motors

We make aftermarket sheet metal body parts at our factory in Gujarat, India, and have done since 1998. For a Massey Ferguson 135 restoration, our panels are pressed from steel sheet and painted in red oxide or grey oxide primer. The minimum order is 5 pieces per product, and we send a sample on request, so you can dry fit one first. We reply to quotes within 24 to 48 hours on business days.

You can see all 11 parts we list for this tractor on the Massey Ferguson 135 parts page. Our tractor bonnet kits page covers the kits for other models. If you also restore the earlier tractor, read how to identify a Massey Ferguson 35. For part names across markets, see our guide to tractor body part names in the UK, USA and India.

Massey Ferguson 135 restoration questions

Which body panels rust first on a Massey Ferguson 135?

Usually the footplates, the battery cover underside, the tool box base and the bonnet seams. These are the places where water and dirt sit. Check them first, because they decide most of the panel budget.

How do I know if my MF 135 has a 13 inch or 14 inch grille?

Measure the grille height on the tractor. Then order the grille and side panels for that size, because UK parts lists sell them separately. If you are unsure, send us a photo with a tape measure in view.

Can I fit new panels next to my original ones?

Yes, but dry fit them first. A new panel beside an old one can show small gaps. It is easier to adjust the panels before painting than after.

Should I repair or replace rusted mudguards?

Repair them if the steel is whole and only the surface has rusted. Replace them if the mounting area is cracked or holed, because that is where the load goes.

Do MF 135 and MF 35 panels interchange?

Some smaller parts are listed for both, such as the tool box. However, the bonnet, grille and side panels differ, so order by model. Send us your model and photos, and we will confirm the fit.

Planning a Massey Ferguson 135 restoration? Send your panel list and photos through our contact page, and we will confirm each part before you order.

Tractor Body Parts Exporter in India Ajva Motors makes aftermarket tractor body parts in Gujarat and exports them. MOQ 5 pieces, sample on request.
View Catalog →

AJVA Motors

Tractor Body Parts Manufacturer & Exporter